Various switch, jumper, slot order and settings are listed below.
DELQA Switch Settings
DELQA and DELQA-PLUS (DELQA-YM) Switch Settings
========================================================================
The DELQA is a Q-bus Ethernet adapter. The usual cabinet kit
provides a 10Base5 (AUI) connector. The DELQA replaces the obsolete
DEQNA.
The standard DELQA (M7516) and the DELQA-PLUS, also known as the
DELQA-YM, "DELQA-T", and "DELQA Turbo" (M7516-YM), use the same hardware
but different firmware.
========================================================================
The 5-position switch sets the mode and CSR address.
Switch 1: CSR: closed: CSR = 17774440 (Default)
open: CSR = 17774460
Switch 2: Reserved: closed (default)
Switch 3: Mode: closed: Normal mode (Default)
Switch 4: Option closed: MOP remote boot disabled (Default)
open: MOP remote boot enabled
Switch 3: Mode: open: DEQNA-lock (compatibility) mode
Switch 4: Option closed: Sanity timer disabled
open: Sanity timer enabled
DELQA:
Switch 5: Reserved: closed (Default)
DELQA-YM:
Switch 5: T-mode: closed: DELQA-T mode enabled (Default)
open: DELQA-T mode disabled
The "sanity timer" may also be called the "host inactivity timer".
========================================================================
In SYSGEN CONFIGURE for a DELQA, specify device "QNA".
DELQA Ethernet Cable Kit
DELQA (DEQNA?) Ethernet Cabinet Kit Cable
This document describes the cabinet kit for a DELQA Q-bus Ethernet
interface board. The kit comprises the AUI connector and fuse assembly
at the bulkhead panel, and the cable from the bulkhead panel to the
DELQA board.
The kit for a DEQNA was similar, and this one would probably work for
a DEQNA, too.
The connector at the board end of the cable is a 2x12 position,
0.1-inch pitch female. The corresponding connector on the DELQA
(M7516[YM]) is a 2x10 male. The outer two pairs of hole on the female
connector are unused, but the male connector accomodates the 2x12 female
connector. The pin numbers shown below are for the 2x10-pin male
connector on the board. The AUI connector is a DB15-S (female). The
fuse on the bulkhead panel near the AUI connector is a 1.5A, 25V,
slow-blow.
DELQA connector, as viewed from cable end.
xx 19 17 15 13 11 09 07 05 03 01 xx
xx 20 18 16 14 12 10 08 06 04 02 xx
=========================================
DELQA Signal Wire color AUI (D.xx) and fuse assembly
01 Power +12V Red fuse tip
02 (nc) (missing on male,
plugged on female)
03 Return 12V (nc)
04 Return 12V Blk D.06
05 Ground (nc)
06 Receive + Wht D.05
07 Receive - Gra D.12
08 Ground (nc)
09 Ground (nc)
10 Transmit + Org D.03
11 Transmit - Yel D.10
12 Ground Bare D.04
13 Ground (nc)
14 Collision + Blu D.02
15 Collision - Grn D.09
16 Ground (nc)
17 (nc) (nc)
18 (nc) Tan D.07
19 (nc) Brn D.15
20 Fuse OK Vio fuse ring
fuse ring --- Org --- D.13
The cable is double shielded. "Bare" is the inner shield. The outer
shield is connected to the bulkhead panel near the AUI connector.
As the author (dimly) recalls, the DEQNA cabinet kit cable had one
fewer wire, presumably not a very important one.
DEQNA Jumper Settings
EQNA Jumper Settings ======================================================================== The DEQNA (M7504) is a Q-bus Ethernet adapter. The usual cabinet kit provides a 10Base5 (AUI) connector. The DEQNA is obsolete (even by Q-bus standards), troublesome, and not supported by VMS since about V5.4. A compatible card, the DELQA, replaces the DEQNA. ======================================================================== Jumper W1 sets the CSR address. Right two pins: CSR = 17774440 (Default) Left two pins: CSR = 17774460 Jumper W2 controls a fair-access timer which provides a delay before re-requesting the Q-bus. Installed: No fair-access wait Removed: 5 microsecond fair-access wait (Default) Jumper W3 disables the sanity timer. Installed: Sanity timer disabled (Default) Removed: Sanity timer enabled ======================================================================== Jumper Locations: \ / +-----------------------------------===========================+ | \ J1 / | | | (Ethernet connector) | | | +----------------------+ | | | | o o-o o-o | | W1 W3 | | | --------------------------------, | | / | | '----------------------------------- | | | | | o o | | W2 | | | | +--------+ | | | | | | | | | +-------------------------+ +-------------------------+ ======================================================================== In SYSGEN CONFIGURE for a DEQNA, specify device "QNA".
KZQSA Jumper Settings
KZQSA Jumper Settings
========================================================================
The KZQSA (M5976) is a Q-bus SCSI adapter.
========================================================================
Jumpers W13 through W9 set the memory base address (bits 21-17, for
the 128kB on-board memory). Jumper removed = 0, installed = 1. (Jumper
W8 is reserved for Digital use, and should not be installed.)
Jumper W W W W W
13 12 11 10 9
MBA bit: 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Binary: j j j j j 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
`-----' `-----' `-----' `-----' `-----' `-----' `-----'
Octal: 0,1 0-7 0,4 0 0 0 0 0
Example, 01000000 (default):
Jumper W W W W W
13 12 11 10 9
R R R I R (R = removed, I = installed.)
CSR bit: 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Binary: 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
`-----' `-----' `-----' `-----' `-----' `-----' `-----'
Octal: 0 1 0 0 0 0 0 0
Having all jumpers installed gives memory base address 17400000,
which is illegal (overlapping the I/O page), and should not be used.
------------------------------------------------------------------------
Jumpers W7 through W1 set the CSR address (bits 12-6). Jumper
removed = 0, installed = 1.
Jumper W W W W W W W
7 6 5 4 3 2 1
CSR bit: 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Binary: 1 1 1 1 1 1 1 1 1 j j j j j j j 0 0 0 0 0 0
`-----' `-----' `-----' `-----' `-----' `-----' `-----'
Octal: 1 7 7 6,7 0-7 0-7 0 0
Example, 17761300 (default):
Jumper W W W W W W W
7 6 5 4 3 2 1
(R = removed, I = installed.) R R R I R I I
CSR bit: 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Binary: 1 1 1 1 1 1 1 1 1 0 0 0 1 0 1 1 0 0 0 0 0 0
`-----' `-----' `-----' `-----' `-----' `-----' `-----'
Octal: 1 7 7 6 1 3 0 0
------------------------------------------------------------------------
Jumpers W14 through W16 set the SCSI ID of the KZQSA adapter. Jumper
removed = 0, installed = 1.
ID2 ID1 ID0
SCSI ID W14 W15 W16
0 0 0 0
1 0 0 1
2 0 1 0
3 0 1 1
4 1 0 0
5 1 0 1
6 1 1 0
7 1 1 1 (Default)
========================================================================
Note that the KZQSA was supported only for CD-ROM and tape, not for
hard disks, but failure with unsupported devices is not certain.
The LED indicates power through the terminator fuse.
========================================================================
In SYSGEN CONFIGURE for a KZQSA, specify device "QZA".
QBUS Slot Map (BA123, BA23)
Q-bus Grant Continuity
------------------------------------------------------------------------
| BA123 |
+-------+
Slot number 13 12 11 12 11 10 9 8 7 6 5 4 3 2 1
A . +--+ +--+ +--+ +--+ +--+--+--+--+
Slot B | | | | | | | | | |
Type C | | | | | | | | | |
D +--+ +--+ +--+ +--+ +--+
------------------------------------------------------------------------
| BA23 |
+------+
Slot number 8 7 6 5 4 3 2 1 (Slot number)
A +--+ +--+ +--+--+--+
Slot B | | | | |
Type C | | | | |
D . +--+ +--+
------------------------------------------------------------------------
TK50 Jumper and Switch Settings
TQK50 Jumper and Switch Settings
========================================================================
The TQK50 (M7546) is a Q-bus controller for a TK50 tape (CompacTape
(tm)) drive. It has two DIP switch sets (hardware revision level and
unit number) and one jumper set (CSR address).
========================================================================
The hardware revision level DIP switch is set to match the module
revision level, which is stamped on the back of the module. The eight
switches represent a binary value: open = 0, closed = 1.
Revision Switch
Level 8 7 6 5 4 3 2 1
----------------------------------
0 0 0 0 0 0 0 0 0
1 (A) 0 0 0 0 0 0 0 1
2 (B) 0 0 0 0 0 0 1 0
3 (C) 0 0 0 0 0 0 1 1
... ...
The unit number DIP switch is similar:
Unit Switch
Number 8 7 6 5 4 3 2 1
----------------------------------
0 0 0 0 0 0 0 0 0
1 0 0 0 0 0 0 0 1
2 0 0 0 0 0 0 1 0
3 0 0 0 0 0 0 1 1
... ...
The VMS operating system does not use these data.
------------------------------------------------------------------------
The jumpers set the CSR address (bits 12-2). Jumper removed = 0,
installed = 1.
/----------- Jumpers -----------\
CSR bit: 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Binary: 1 1 1 1 1 1 1 1 1 j j j j j j j j j j j 0 0
`-----' `-----' `-----' `-----' `-----' `-----' `-----'
Octal: 1 7 7 6,7 0-7 0-7 0-7 0,4
Example, 17774500 (default):
/----------- Jumpers -----------\
CSR bit: 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Binary: 1 1 1 1 1 1 1 1 1 1 1 0 0 1 0 1 0 0 0 0 0 0
`-----' `-----' `-----' `-----' `-----' `-----' `-----'
Octal: 1 7 7 7 4 5 0 0
========================================================================
Jumper and Switch Locations:
\ /
+===========================-----------------------------------+
| \ J1 / |
| | (Drive cable connector) | |
| +-------------------------+ |
| |
--------------------------------, |
| / |
| '-----------------------------------
| CSR |
| |
|A12 o-o |
|A11 o-o |
|A10 o o Hardware |
|A09 o o Revision |
|A08 o-o Level |
|A07 o o +---+ |
|A06 o-o | 1 | |
|A05 o o | 2 | Unit |
|A04 o o | 3 | Number |
|A03 o o | 4 | +---+ |
|A02 o o | 5 | | 1 | |
| | 6 | | 2 | |
| | 7 | | 3 | |
| | 8 | | 4 | |
| +---+ | 5 | |
| | 6 | |
| | 7 | |
| | 8 | |
| +---+ |
| |
| +--------+ |
| | | |
| | | |
+-------------------------+ +-------------------------+
========================================================================
In SYSGEN CONFIGURE for a TQK50, specify device "TU81".